Simer 3075SS-01 Bedienungshandbuch PDF herunterladen (Seite 6)

Installation / Operation 6

For parts or assistance, call Simer Customer Service at 1-800-468-7867

ELECTRICAL CONNECTION

Hazardous voltage. Risk of dangerous or

fatal electric shock. Plug the pump into a 115 Volt,

60 Cycle, Ground Fault Circuit Interrupter (GFCI) pro-

tected grounded outlet only. The pump is equipped with

a 3-wire grounded cord and plug. Do not modify or

remove the plug. Make sure the outlet meets the

National Electric Code or the Canadian Electrical Code,

as applicable. To avoid dangerous electrical shock haz-

ard, keep the cord dry at all times. See Figure 2.

AUTOMATIC PRESSURE CONTROLLER

The Automatic Pressure Controller mounts on the pump.

It protects against:

• Run-dry operation;

• Frequent starts caused by small water losses in the system;

• Pressure drop.

The Automatic Pressure Controller features the following

LEDs and controls:

‘Power on’ LED: indicates that the unit is electrically

connected and that voltage is present. The pump is ready

to operate.

‘Pump on’ LED: indicates that the pump is running and

actually pumping water.

‘Failure’ LED: indicates that no water is detected coming

into the pump.

‘Restart’ button: resets any safeties which have tripped

and allows the pump to restart.

NORMAL OPERATION

OF THE ACE-IN-THE-HOLE

AUTOMATIC BOOSTER PUMP

Burn Hazard. NEVER run the pump dry.

Running the pump without water may cause pump to

overheat and cause burns to persons handling the pump.

It may also damage the impeller and may damage the

seal, causing leaking or flooding, and will void the war-

ranty. Fill the pump with water before starting it.

Make sure that the Ace-In-The-Hole Automatic Booster

Pump has been properly installed, primed (see page 4),

and that the suction pipe is unobstructed and open.

Plug in the pump. The ‘Power on’ and ‘Pump on’ lights

will come on indicating, respectively, that voltage is pre-

sent and that the pump is ready to operate.

The pump will start and will continue to operate until

several seconds after the system pressure has risen and

flow has stopped.

WHEN DOES THE PUMP

STOP OPERATING?

Pressure Set-Point/No Flow: The pump will stop operat-

ing and the ‘Pump on’ LED will go off several seconds

after:

• The system pressure is above the starting pressure, and

• The flow has stopped.

This is normal operation.

Restart: A water flow in the system greater than

1/4 GPM or a drop in pressure below the starting pres-

sure set-point will cause the pump to restart and the

‘Pump on’ LED to light up. The pump will continue to

operate until several seconds after:

• It reaches the maximum pressure of the pump, and

• The flow stops.

NOTE: The delay in shutting off the pump prevents

rapid cycling when water faucets are being turned on

and off quickly (for example, when brushing teeth, etc.).

Pressure Drop/No Flow: Normally, when the pump

starts, it will very quickly generate pressure and sense

flow. If there is no flow and the pressure does not rise, it

senses a “no water” condition. It can also sense this dur-

ing operation if the water supply to the pump fails. To

protect the pump from running dry:

• Several seconds after it detects “no water”, the pump

will stop operating,

• The ‘Pump on’ LED will go out, and

• The ‘Failure’ LED will go on.

‘Power on’ LED

‘Pump on’ LED

‘Failure’ LED

‘Restart’ Button

5682

Figure 4 - Ace-In-The-Hole Automatic Booster Pump

Control Panel

1 2 3 4 5 6 7 8 9 10 11 ... 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

Simer 3075SS-01 Bedienungshandbuch Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Wasserpumpen Simer 3075SS-01